As titled, Alientech KESS3 and Autotuner which is better for beginners? Here is the clue. Both are excellent tools to start with, both well supported and respected in the industry. You cant go wrong with either, the right choice often depends on the type of vehicles you plan to work on and how you… Read More »
How safe/reliable is Autotuner for ZF 8HP gen3 gearbox TCU? This capability was released around six months ago. Is it safe and trouble free? It works great. All good, stable work. Done at least 50 cars with gen3. Keep the voltage above 12.5V . Works also on newer gen3 from m3 lci, etc. Example: flashed… Read More »
XirDecoder ECU chip tuning tool now supports Ford – SID212 ECU. ALL MAPPACK Added! Supported features: • DTC • DPF • EGR • LAMBDA • SCR • STAGE1 • TORQUE MONITOR • TVA • VMAX
XirDecoder ECU chip tuning tool released new protocols for MD1CS069, MD1CS089 and EDC17CV41 ECUs. Iveco – MD1CS069 ECU Supported features: • DTC • CAT • EGR • LAMBDA • MAF • TVA The New Holland MD1CS069 XIRDecoder now supports: DTC CAT EGR TVA The XIRDecoder for MD1CS089 ECU now supports: DTC CAT EGR LAMBDA… Read More »
Formulaflash ECU programmer released new software version 1.1.4.0 on March, 10th, 2026. Enhanced Upgrade Toyota GEN2 adapter-free read/write + verification (no disassembly, no adapter required) ME7.8 VIN mismatch / unable to read VIN fix ME7.8+ ME7.8.8 GEN2 unlock upgrade (expanded CAN communication + K-line vehicle model unlocks) ME7.8+ ME7.8.8 CAN communication, PC version adapter-free,… Read More »
World Exclusive! Alientech KESS3 ecu programmer introduces the Bench protocol for Ford Continental SID212 ECUs. One of the most requested ECUs on the market can now be worked on directly in the workshop with KESS3. 11.03.2026 – Upgrade 2.96 Alientech further expands the operational possibilities offered by the KESS3 platform with the release of the… Read More »
Autotuner released a BETA OBD protocol for Mighty 4JJ1. AT just added support for the Delphi 4J ECU powering the legendary 3.0 TD engine. Supported Models: Isuzu D-Max & MU-X Holden Rodeo Method: OBD Virtual Read (BETA) Fast and efficient! Get the original file from our server directly via the OBD port. Try it out… Read More »
It’s a Hyundai i20 with Delphi ECM6.2AP ECU. Foxflash read and write this ECU in boot mode. Read 8 minutes/write 10 minutes. Read ok, Write ok. Checksum correction with foxflash. DPF and dtc off. All ok.
Iveco Bosch MD1CS069 Now Ready! New Flex update, version 7.49.0.0, now available, implementing OBD programming for the most modern Iveco vehicles equipped with Bosch MD1CS069, even those produced after 2021. Thanks to this new protocol, you can now work directly from the diagnostic port of the vehicle (bypassing the SGW module), or establishing direct connection through the connector. As of… Read More »
New protocol released of Magic Motorsport Flex programmer for Continental SID213 and SID213EVO engine units installed on new gen Ford and Volkswagen vehicles. This new solution is made to work on vehicles with 2.0L EcoBlue and 2.0L TDI engines. A new protocol that opens access to the map area via OBD connection, therefore… Read More »
Problem: I read a Nissan Bosch edc16cp33 ECU with Foxflash today and after the car did not start, having two errors. The vehicle is equipped with smart Go keys Through obd I did the computer reading and also the injector codes.. After writing the mod file the vehicle will not start. The key is on… Read More »
FormulaFlash ecu programmer read and write VW 1.6TDi Delphi DCM6.2V ECU in boot mode successfully. 1.Read password Before connection, read the paddword and back up password file. Back up password file successfully. 2. Read flash in boot Set up boot connection. Load the backed up password file, read intFlash data in boot and… Read More »
Problem: Tried to read an Audi Bosch MG1CS011 TC298 ECU with Autotuner and Alientech KESS3 programmer. Both devices failed to read this ECU via OBD. Trid to bench it with kess3. It showed no support for this ecu. Any idea? Solution: No way after 06/2020. No virtual file no way. This hw version is really… Read More »
Good news! Launch X431 ECU & TCU programmer new V10.51 version software added Benz VGS4 bench mode without removing the shell as previous version. Here iecutool.eu will show how to erase/virgin and clone Benz VGS4-0-NAG2 4-speed transmission gearbox TCM on bench mode. This step-by-step guide helps technicians safely erase transmission control data and prepare the… Read More »
Foxflash new user report: It’s an Isuzu Dmax 2007 3.0d. DCM6.2 Delphi ecu Mpc56x Foxflash read it via obd on bench. Used multimultional adapter without benchbox. “Obd protocol read ok. Took 1hr to read. Awaiting for a 5-6 amper power supply for writing to be safe. You can also use OTB adapter on this or… Read More »
