Problem: The XRemover ECU tuning software stopped working, it got stuck on this interface and will not continue. Solution: The update process was interrupted because the user wasn’t using administrator privileges. Restarted the upgrade process with administrator privileges and completed the remaining steps.
Massive time saver: Iveco EDC16C39 live via 100% OBD! No more ECU removal! You can now flash the iconic Iveco commercial vans directly through the diagnostic port with your AutoTuner Tool. Coverage: Iveco Daily (2.3 & 3.0 HPI/HPT engines) Iveco Massif (3.0 HPI engine) Method: 100% OBD (Normal Read). Plug in, read, write. The perfect… Read More »
Problem: Trying to read an Audi Bosch DQ381 gearbox with CG FC200 ecu programmer on bench but failed to connect with this TCU. It says error “E111 Security Authentication Failed”, Any solution? Solution: The boot version is bh1g0401. This is generation 2 bootloader 401. You can not read it with fc200. Software too new and… Read More »
The Jaguar Land Rover update is massive! JLR MD1CP007 / MD1CP017 / MG1CS028: Live on Bench (after Mail-in Unlock)! Tune the latest MHEV & PHEV powertrains (Diesel & Petrol) up to 510hp with your AutoTuner Tool. Diesel 2.0L & 3.0L MHEV: Land Rover Defender, Discovery & Discovery Sport Range Rover, Range Rover Sport, Velar Petrol… Read More »
CGDI released a new DAP adapter that is designed to read both EEPROM and Flash data from Delphi ECUs. Here iecutool.eu will show how to read a Hyundai Delphi DCM7.1AP ECU with CG FC200 programmer and DAP adapter. Select Hyundai- Delphi DCM7.1AP TC277T ECU and choose boot mode. Check wiring diagram. Connection Setup: 5 wires… Read More »
Autotuner new protocol- Bosch MD1CS069 (Agri & LCV): Live on Bench (after Mail-in Unlock)! The professional market is calling! The Bosch MD1CS069 ECU (FPT Euro 6d & Stage V engines) is now supported on your AutoTuner Tool. Massive Coverage: Iveco Daily, Fiat Ducato (2.3 & 3.0 HPI / Multijet) Mitsubishi Fuso Canter New Holland, Case… Read More »
Read and write Nissan/Infiniti MED17.7.2 ECU with CG FC200 programmer successully. Quick search MED17.7.2 ECU. Use platform mode (bench mode). Check wiring diagram. Connect ECU with FC200 via FC200 ECU adapter. Read Dflash and Pflash ok. Write Dflash and Pflash ok. IMMO OFF ok. Immo off in device without 3rd party device. Images attached:
Problem: I’m having trouble reading my DL501 gearbox at foxflash programmer. I have to disconnect and re-connect several times, but the reading remains stuck at 0% . Any solution? Solution: You need Bench MFC cable. You need to use multifunction cable that is included in foxflash kit. There is a ignition switch. 12v+ and 12v… Read More »
XIRDecoder New Support Added! XIRDecoder support for Hyundai–KIA – MD1CS012 ECU. Supported features: * DTC * DPF * EGR * LAMBDA * MAF * SCR * STAGE1 * TORQUE MONITOR * TVA * VMAX
Problem: Tried to read BMW E60 CAS3+ module with Xhorse Multi Prog, I keep receiving ID identification failed message. Any solution? Solution: BMW CAS3+ ID failed is usually wrong connection or no ignition wake up. Use adapter mode not direct and make sure all power and ground stable. Also check you selected correct cas3 plus (CAS3+)… Read More »
Foxflash read and write Citroen ME7.4.4 ECU successfully. Mode: Citroen Saxo VTS 120 HP ECU & protocol: ME7.4.4 Full system Read: 2 min Write: 3 min No checksum. Car start. Immo Off in EEPROM and FLASH. Images attached:
Question 1: When I import a file to write in Dimsport The Genius programmer it doesn’t put it in the write folder? How to find the imported files in The Genius? Answer: If you use Race EVO to edit it, the file goes into Bench or Obd, if you use another software it’s all… Read More »
In the latest software update of the CG FC200 ecu programmer, the J2534 function has been added. We are able to use the FC200 as a J2534 passthru device together with PCM-Flash software. Below, we demonstrate how to use the J2534 function of the FC200. ECU example: Geely Easy U2. Note: Like other J2534 devices,… Read More »
