Problem: I need to perform an “immo off” on a 2010 Chevrolet Aveo with a Delphi MT80 ECU. I’ve used the FoxFlash pinout, but I can’t get it to connect. Can anyone give me a hand? Here is the clue. Suggestions: 1). Increase voltage, give power supply at 14.5V. 2). Use a 120-ohm resistor between… Read More »
Foxflash programmer new user report today: Read password: Read password from OBD. Use the godiag gt100+ to read the password via OBD on bench mode without the car. Read/write: Full read and write was done via BDM. Cloned it successfully. Checksum by foxflash.
Foxflash programmer software update to V1.4.3.5. FoxFlash 1.4.3.5 Update Announcement Release Date: September 17, 2026 (Malta Time) Status: Rolling out gradually What’s New in Version 1.4.3.5 • Three Virtual Servers Added three virtual servers with powerful anti-interference capability and automatic switching for more stable and reliable connections. • VAG Simos18 Virtual Database Update Updated… Read More »
Read and write BMW G30 530xd 2018 Bosch MD1CP002 ECU with Foxflash programmer successfully. ECU: MD1CP002 Stage1 Read-bench Write-bench Checksum manually. Foxflash works with md1/mg1 till 06/2020. Till 2021 may after this date all are locked by BOSCH. You need Flex/KESS3/OBDSTAR etc.
Foxflash programmer read and write VW Golf 7 Bosch EDC17C64 ECU successfully. VW Golf 7 year 2015 ECU: EDC17C64 Bench mode. Read ok Write ok EGR OFF CVN Checksum by Foxflash Voltage: 13.8V
It’s a BMW F10 530d with Bosch EDC17C41 ECU. Successfully cloned ECU using Foxflash programmer on bench mode. Read EEPROM and IntFlash from Original ECU. Read IntFlash from Donor ECU. Use Clone tools and combine ORI and DONOR Intflash because of setting up OTP sectors and save new IntFlash file (important step). Use the cloning… Read More »
Peugeot PSA DCU-102 ECU was killed by Autotuner via OBD mode. Restored/recovered by FoxFlash in boot. Because dcu102 autotuner have only “beta” obd protocol. Check your laptop usb ports, usb cable, autotuner obd cable too , on original obd cable pins very thin, some users use obd extension 0.3m for stable connection, especially for PSA… Read More »
Read and write Ford Kuga DCM6.1 ECU with Foxflash programmer by OBD successfully. Ford Kuga 2016, 2.0, 110kw, ECU: DCM6.1 Mode: OBD HW: DS71-12B684-XB Read by foxflash. Checksum correction with foxflash. Write by foxflash. A short story. A quick internet search for the ecu identification numbers gave me a result that the ecu was DCM3.5… Read More »
Problem: Foxflash read Mercedes Benz Delphi CRD2 ECU via OBD ok (100% without problem), Wanted to write. Get ID – load file. Click write. And didn’t even started. Got this message, and now ecu is in brick. Car can’t start. What to do to wake up ecu? Solution: CRD2 is tricky, especially for entry-level tools.… Read More »
Foxflash ecu programmer new user feedback today: ACDelco E83 ECM. Jtag connection Opel Astra J 1.4 g Read/Write ok by foxflash. Foxflash says no checksum. Writing without calculation ok. Why do it via Jtag mode? OBD mode also works. But Obd mode gives not full dump. Do it in Jtag if need full dump. … Read More »
Renault Clio IV EMS3125 ECU, foxflash can do a full reading?? Can you clone? The OBD reading in the car works, but you can’t read the password, tries to be 3155. Nothing can be done on the table either, both OTB and BOOT. What other device can full read and clone this ECU? Foxflash:… Read More »
Foxflash read and write PSA MED17.4 ECU successfully. Peugeot 207 RC 1.6 thp 175 ch MED17.4 Boot Tricore mode Med17.4 Tc1766 Read/Write ok. Checksum by foxflash ok. If need to clone this ECU, go into Boot menu and select tricore cloning, prepare flash, write modded flash, write original eeprom.
Foxflash read and write VW Tiguan 2020 2.0 TSI Bosch MG1CS001 ECU successfully. MG1CS001 before 2020-06 FoxFlash Bench mode. Read/Write ok. Checksum by foxflash. Use a regulated power supply (5A). 14V voltage on bench. Before handing the car back to the customer, make sure to check for misfires and whether the ignition timing is being… Read More »
Problem: Tried to read Audi DQ250 gearbox with foxflash programmer. It says seedkey error, on obd it says error sk2 seedkey. On bench without Benchbox it says error sk1 seedkey. Try to read by K-line. Can do ID no problem on both obd and bench. They’re not coming something with switch power on, this error… Read More »
User working experience on reading and writing Fiat Ducato 2021 Marelli 9DF ECU using Foxflash programmer. Marelli 9df Ducato 2021 Fiat Ducato 2021 2.3MJet 140HP. Read: Bench obd, full ok (2 hours) but don’t write by Foxflash. Read/Write Jtag ok but very long time. Read takes 15 minutes, write 27 minutes. Adblue and stg1. Checksum… Read More »
