Author Archives: sales

FormulaFlash V1.0.8.0 Adds More Volvo Opel JLR Benz ECUs

FormulaFlash ECU TCU programmer released new software version 1.0.8.0 on December 1st, 2025. V1.0.8.0 Adds following ECU types: Volvo EDC15C11-3.XNO1 EDC15C11-4.X250KNO1 EDC15C11-4.X500KNO1 EDC15C11-3.XNO2 EDC15C11-4.X250KNO2 EDC15C11-4.X 500K NO2 EDC15C3 KLINE NO1 EDC15C3 KLINE NO2 EDC15C7 KLINE Opel ME1.55 KLINE ME7.6H4 KLINE ME7.6.1 KLINE ME7.6.2 KLINE ME7.6.1 KLINE ME7.6.2 KLINE JAGUAR P3.ONA 4.2SC, 4.2 V8 V8SC, 4.2SC… Read More »

OBDSTAR G3 Read and Write Peugeot DCM6.2C ECU, DTC OFF

OBDSTAR X300 Classic G3 worked very well today, had to do DTC off on a Peugeot boxer dcm6.2c. ECU type: DCM6.2C Mode: Boot mode. Read ext eeprom and int flash ok. Write eeprom and flash ok. Only had DCM6.2A listed but I know the pin out is the same. Worked great with fast read and… Read More »

Foxflash No Red Light on Bench Box and Switch Solution

Problem: No red light on Foxflash programmer bench box and switch, has happened to anyone? Solution: Light comes only when tool start reading, when it says keep ecu power on make sure switch is at 1, then press ok that’s when the light will come Power will only come on in bench mode after the… Read More »

Foxflash Read and Write Ford Connect 2019 MD1CS005 ECU

Foxflash read and write Ford Connect MD1cs005 ECU on bench successfully. ADblue off. MD1cs005 Read/Write on Bench. Checksum by foxflash. Voltage 13.5.

Foxflash VW DCM6.2V ECU Car Not Start Solution

Problem: How do I read and write down a driver in a vw dcm6.2v with foxflash in boot mode, because after installing stage 1 (via OBD) the car does not start and I can’t bet anything? Solution: That situation usually comes from checksum handling or wrong patch area – DCM6.2V is picky. If you can… Read More »

Foxflash ‘Subscription is About to Expire’ Solution

Problem: I have this alert today when I open the Foxflash software. It says the subscription is about to expire. Solution: Ignore, there’s no subscription. Hit OK and continue.

Foxflash Read and Write BMW 520d EDC17C41 ECU

Read and write BMW 520d EDC17C41 ECU with Foxflash successfully. Read ok. Write ok. Checksum correction. Stage 2, EGR off. Car feeling great.

Foxflash Read and Write Opel Astra Denso 64F7059 ECU

Foxflash read and write Opel Astra 1.7Cdti 125HP 2012 ECU successfully. ECU type: Denso 64F7059 Dpf Off ok. Read/Write Full Bench without Bench Box. Checksum by foxflash.

Foxflash Read and Write SSANGYONG Delphi DCM3.2AP

It’s a SSANGYONG ACTYON 2009, 2.0, 104kW. ECU type: Delphi DCM3.2AP Tool used: Foxflash Mode: BDM mode. BDM MPC 55x/56x full backup with foxflash. Checksum correction by foxflash, IMMO OFF ok. ST95320 eeprom write back with TL866II programmer for set write protect.

KESS3 Adds OBD Protocol for Ford MG1 MD1 ECUs!

24.11.2025 – UPGRADE 2.65 The protocols you were waiting for are now finally active on Alientech KESS3. Ford’s evolution continues through increasingly efficient powertrains, new electronic management systems, and Bosch platforms designed to enhance performance and safety. With this update, KESS3 takes a decisive step forward, enabling OBD access to the latest-generation MD1 and MG1… Read More »

OBDSTAR DC706 Read Hyundai SIM2K-251 in Boot

OBDSTAR DC706 read and write Hyundai SIM2K-251 ECM in boot mode successfully. With MP001 programmer in boot mode. First tried SIM2K-251 in boot, no luck. Sim2k-251 be able to read with sim2k-250 in boot mode. Checksum correction by DC706. Immo off on Sim2k-251 is not working. SIM2k-250 don’t have immo off options as you see… Read More »

Xhorse Multi Prog Read and Write Maserati BCM BSI MC9S12DG256

Read and write the Maserati BCM/BSI module with Xhorse multi prog successfully. MASERATI BCM Type: Magneti Marelli BSI Processor: MC9S12DG256 unsecured Read mcu, eeprom and flash successfully on bench mode. vvdi prog will also read this BCM.

KESS3 Update CompAir Landini McCormick HJS ACU in Boot

Alientech KESS3 released new protocol fpr HJS ACU- CompAir, Landini, McCormick. Operate in BOOT mode on next-generation agricultural and industrial machines, expanding your service options on some of the most requested work vehicles in the field. Read and write in BOOT mode on the HJS ACU control unit Work with precision on 4.5L and 6.7L… Read More »

Foxflash Clone Renault SID306 ECU in Boot

Renault SID306 ECU cloning is done with Foxflash programmer. Continental Sid306 Infineon TriCore SAK-TC1766 boot mode clone ecu. Need attention for pinout because very small in ecu pin. Cloning cannot be done on bench. Read in boot ok. Write in boot ok. Checksum by foxflash. Better keep power supply 12V+.

KESS3 Update MAN Truck Continental PTM5 in Boot

Alientech KESS3 released new protocol for Continental PTM5- MAN 12.4L trucks. Operate in BOOT mode on European heavy-duty vehicles thanks to the latest update dedicated to MAN engines. Read and write the ECU in BOOT mode. Work safely on 12.4L engines across the most reliable MAN series. Improve efficiency and overall performance on long-haul and… Read More »