The Magic Motorsport Korhex boot glitch adapter has several different MASKs: A, B, C, D, E, F, G. Which ECUs does each of these MASKs support? Check here. A Mask: Delphi ETC3 B Mask: MG1CS032 C Mask: for feature (not available yet) D Mask: MG1CA920 E Mask: MD1CP001 F Mask: MD1CS003 G Mask: MD1CP007/ MG1CS047… Read More »
Problem: Tried to unlock a Mercedes MD1CP007 ECU with Flex + Korhex programmer. What concerns me is the LED status: Software shows Connected Antenna: Ready Voltage: 19 V But the RGB LED near the USB/power connector keeps flashing red continuously According to the Korhex manual, flashing red indicates an error condition related to voltage or… Read More »
Korhex: New Support for Bosch MD1CS069 and MD1CS089. Flex version 8.26.0.0 is now available Unlock Bosch MD1CS069 and MD1CS089 ECUs without working on the PCB. With the latest Flex update, Korhex can now also be used on ECUs installed on commercial and industrial vehicles, accessing the TriCore TC299 processor through a dedicated procedure. The new… Read More »
Formulaflash read and write BMW MEVD17.2.4 DME ECU successfully. Read/write flash ok. Read/write eeprom ok. Clone ok. Checksum correction with FormulaFlash. Edit VIN ok. Modify ISN ok. IMMO OFF ok. Too many features were integrated into this device. Don’t need 3rd party software/tool.
Full bench clone of VAG DQ200 MQB DSG control module using FormulaFlash programmer successfully. Select DQ200 MQB gearbox TCU-Bench mode. One button reading original Micro/EEPROM data (Read All) and transferring it directly to the donor TCU—no immo adaptation needed. Read all and save. Connect a donor DQ200 MQB TCU with formulaflash. Then do Write All… Read More »
XirDecoder ECU chip tuning software released new ECU tuning solution: MAHINDRA Bosch MD1CS018 ECU. NEW MAHINDRA MD1CS018 SOLUTIONS AVAILABLE ON XirDecoder! We are excited to announce new Mahindra MD1CS018 ECU solutions, now available on XirDecoder. DTC Off CAT Off EGR Off Lambda Off MAF Off NOx Off Torque Monitor Off TVA Off Powerful solutions. Faster… Read More »
Autotuner Peugeot 208 1.6 THP 200 Bosch MEVD17.4.2 ECU tuning review: This wasn’t an OBD-and-done job. The ECU arrived by post and required direct boot-mode access, meaning the ECU had to be opened, connected directly to the PCB and read at processor level before any work could begin. That is exactly the kind of work… Read More »
HEAVY DUTY RELEASE: TRW VOLVO EMS2.3 & EMS2.4 go live on Bench Normal Read! A major software update targeting commercial heavy transport, construction, and specialized industrial/agri machinery has landed on your equipment! TRW VOLVO EMS2.3 and EMS2.4 ECUs are now officially supported via Bench Normal Read (NR) on your AutoTuner Tool. Note: Specific datalogs… Read More »
Unlocked an E90 ECM of a 2022 Chevrolet Cheyenne with Formulaflash Programmer successfully. The 2022 Chevrolet Cheyenne is the Mexican-market counterpart to the refreshed full-size Chevrolet Silverado 1500, featuring updated styling, improved cabin tech, and a new flagship off-road trim. Bench mode. How to unlock with formulaflash? Hit Unlock Protection to unlock ECU on bench… Read More »
Alientech KESS3 released new BOOT unlock protocol for Bosch MG1CS028 “Locked” ECUs- Jaguar and Land rover. KESS3 expands its coverage of latest-generation JLR vehicles equipped with Ingenium turbocharged petrol MHEV and PHEV engines, from 2021 onwards. New BOOT Unlock protocol using the dedicated KESS3 Unlock Module BENCH mode already available for a more flexible workflow… Read More »
Problem: I need to perform an “immo off” on a 2010 Chevrolet Aveo with a Delphi MT80 ECU. I’ve used the FoxFlash pinout, but I can’t get it to connect. Can anyone give me a hand? Here is the clue. Suggestions: 1). Increase voltage, give power supply at 14.5V. 2). Use a 120-ohm resistor between… Read More »
Alientech KESS3 released new Bench and Boot unlock protocols for Bosch MD1CP017 locked ECUs- Jaguar and Land rover. KESS3 expands its coverage of latest-generation JLR diesel MHEV vehicles equipped with 2.0 D165 and D200 engines, from 2021 onwards. Unlock protected Bosch MD1CP017 ECUs using the dedicated BOOT protocol and KESS3 Unlock Module Read and… Read More »
Formulaflash programmer read and write a Ford Focus DPS6 dual-clutch transmission gearbox TCU successfully. Bench mode. Read eeprom & flash ok. Write eeprom & flash ok. Checksum correction with formula flash.
XirDecoder ECU chip tuning software released new version 3.9 on October 9th, 2026. v3.9 [9.10.2026] – Fixed various program interface issues. – Improved the overall interface layout. – Updated button designs. – Refined visual interactions throughout the program. – Improved support for a wide range of ECU models. – Made ECU-specific processing improvements. –… Read More »
ECUDesk ECU remapping software development team is introducing a new client application— a mini-app that runs within Telegram. Now you can take your favorite app with you wherever you go; all you need is your mobile phone! It’s simple: Dear ECUDesk users! 1 accounts for 2 pcs and 1 phone!!! It’s simple: 1. Follow the… Read More »
