How safe/reliable is Autotuner for ZF 8HP gen3 gearbox TCU? This capability was released around six months ago. Is it safe and trouble free? It works great. All good, stable work. Done at least 50 cars with gen3. Keep the voltage above 12.5V . Works also on newer gen3 from m3 lci, etc. Example: flashed… Read More »
Formulaflash ECU programmer released new software version 1.1.4.0 on March, 10th, 2026. Enhanced Upgrade Toyota GEN2 adapter-free read/write + verification (no disassembly, no adapter required) ME7.8 VIN mismatch / unable to read VIN fix ME7.8+ ME7.8.8 GEN2 unlock upgrade (expanded CAN communication + K-line vehicle model unlocks) ME7.8+ ME7.8.8 CAN communication, PC version adapter-free,… Read More »
World Exclusive! Alientech KESS3 ecu programmer introduces the Bench protocol for Ford Continental SID212 ECUs. One of the most requested ECUs on the market can now be worked on directly in the workshop with KESS3. 11.03.2026 – Upgrade 2.96 Alientech further expands the operational possibilities offered by the KESS3 platform with the release of the… Read More »
Autotuner released a BETA OBD protocol for Mighty 4JJ1. AT just added support for the Delphi 4J ECU powering the legendary 3.0 TD engine. Supported Models: Isuzu D-Max & MU-X Holden Rodeo Method: OBD Virtual Read (BETA) Fast and efficient! Get the original file from our server directly via the OBD port. Try it out… Read More »
It’s a Hyundai i20 with Delphi ECM6.2AP ECU. Foxflash read and write this ECU in boot mode. Read 8 minutes/write 10 minutes. Read ok, Write ok. Checksum correction with foxflash. DPF and dtc off. All ok.
Iveco Bosch MD1CS069 Now Ready! New Flex update, version 7.49.0.0, now available, implementing OBD programming for the most modern Iveco vehicles equipped with Bosch MD1CS069, even those produced after 2021. Thanks to this new protocol, you can now work directly from the diagnostic port of the vehicle (bypassing the SGW module), or establishing direct connection through the connector. As of… Read More »
New protocol released of Magic Motorsport Flex programmer for Continental SID213 and SID213EVO engine units installed on new gen Ford and Volkswagen vehicles. This new solution is made to work on vehicles with 2.0L EcoBlue and 2.0L TDI engines. A new protocol that opens access to the map area via OBD connection, therefore… Read More »
Problem: I read a Nissan Bosch edc16cp33 ECU with Foxflash today and after the car did not start, having two errors. The vehicle is equipped with smart Go keys Through obd I did the computer reading and also the injector codes.. After writing the mod file the vehicle will not start. The key is on… Read More »
FormulaFlash ecu programmer read and write VW 1.6TDi Delphi DCM6.2V ECU in boot mode successfully. 1.Read password Before connection, read the paddword and back up password file. Back up password file successfully. 2. Read flash in boot Set up boot connection. Load the backed up password file, read intFlash data in boot and… Read More »
Problem: Tried to read an Audi Bosch MG1CS011 TC298 ECU with Autotuner and Alientech KESS3 programmer. Both devices failed to read this ECU via OBD. Trid to bench it with kess3. It showed no support for this ecu. Any idea? Solution: No way after 06/2020. No virtual file no way. This hw version is really… Read More »
Foxflash new user report: It’s an Isuzu Dmax 2007 3.0d. DCM6.2 Delphi ecu Mpc56x Foxflash read it via obd on bench. Used multimultional adapter without benchbox. “Obd protocol read ok. Took 1hr to read. Awaiting for a 5-6 amper power supply for writing to be safe. You can also use OTB adapter on this or… Read More »
It’s a BMW 3D 184hp with Bosch EDC15C4 ECU. Tried Foxflash Full mode but not working(connected everything as shown, measured cables, resistors, outputs everything with multimeter and it’s 100% fine but still no connection) – ERROR SEND WAKE. Simulated OBD on BENCH via K-LINE ok. READ – 5 min WRITE – 2 MIN ONLY FLASH… Read More »
Here is the real user’s working experience on VW Passat B7 EDC16CP46 ECU cloning using foxflash: It’s a VW Passat B7 2013 CFFB with Bosch EDC17C46 ECU. The ecu was broken, car didn’ t start, reading on bench was not working. The car wouldn’t start, some water had gotten into the ecu through the plastic… Read More »
How to simulate OBD for Land rover Bosch EDC15C4 ECU using Foxflash programmer? obd simulation worked with the Godiag GT100 breakout box. It worked with car OBD not full system. Full system doesn’t work. Full system is not about OBD. Just do standard pinout. Read with obd protocol without resistors just k line and… Read More »
Problem: I’m having trouble reading this bsi off a Ford Ka (Fiat 500) with OBDSTAR DC706 on bench mode. Tried with and without 120 ohm, no luck. Any suggestions? Solution: Select Ford BSI (Ford BSI Delphi 70F3379+93C86) rather than Fiat BSI. Don’t forget to connect a power supply. Update: Fixed. Important to select Ford… Read More »
