Problem: Just bought myself FoxFlash to clone dq400e. It gets ecu data but does not read. Am i doing something wrong? Solution: You have to follow instructions correctly. Pres ok then turn key on not before. Otherwise will fail to get id. Same thing happens on DQ250 MQB. Option 2: Or read via obd… Read More »
Here are the instructions on reading and writing DSG DQ250 MQB gearbox TCU by foxflash users. This one really worked. read/write the transmission, the tool foxflash, godiag (autopower/manual power+ 120ohm) bench method was used Connection: 1-foxflash (power supply 13,4V)-orange cable OBD to godiag- DSG DQ250 MQB cable pinout: DSG connector pin 1- kline to bench… Read More »
Foxflash User feedback: Yesterday one of my genuine tools bricked the DCM3.5 ECU by obd, dimsport couldn’t give any help. flash simple ecu with simple off solution with a genuine tool on obd with good battery voltage. it’s simple egr off with genuine davinci deluxe, battery etc all good, totally stock file before, it happens.… Read More »
Here is a complete list of the tested ECU’s by the tool Foxflash. EDC16U1 bench full read and write EDC16U34 bench full read and write EDC16U31 vw – the crazy additive diesel (BRT) bench full read and write (OBD not possible but KESS v2 worked OK) EDC17C64 vw bench full read and write EDC17C46 vw… Read More »
Problem: Tried to read Peugeot Bosch MD1CS003 ECU 0281037200 with FoxFlash programmer but failed. Error SK2 bench locked. Can Autotuner or Hexprog2 do them? Solution: They are not locked till around 2021. Done a lot of them with foxflash 2018-2021, this one is from 2022 and is locked. 0281 034 708 OK 0281 034 826… Read More »
Question: I just bought FoxFlash to read my MEVD 17.4.4 Peugeot 308 GT 205 hp and I need some advice Is 12V enough or is 14V better? Once the play is done I edit the file with WinOLS 4.7 I have a mappack and do I have to do something else before I write the… Read More »
Problem: Mercedes VITO, edc16c2 ECU. Foxflash read ok via OBD, OBD Write ok but car doesn’t start. Solution: It was tested to work couple times so far, but maybe checksum wasn’t done with foxflash on this case. Checksum is fucked up. If read with foxflash, power supply is important. Radiator turning on while writing. If car does not… Read More »
Problem: I have a problem with Foxflash. Cannot open Manager to activate foxflash software. Error “Only one instance at a time”. How to fix it? Solution: It’s already running. Restart your computer for starters. Open manager once. If you’re not seeing anything install dotnet framework 4.7 and timesync auto to off. www.iecutool.eu
Problem: Foxflash failed to read VW Simos 18.1 tc1792 ecu in boot mode. I have 14.5V And checked Pinout 2 times. There’s always this error (no response with ECU) and wake error. Any solution? Solution: 1). Voltage issue. Set to 13v. Too much voltage at the moment if 14.5v. Some ecus need very specific voltage, start allways… Read More »
Problem: Failed to install foxflash software 1.4.3. It reported an error “The code execution cannot proceed because VCRUNTIME140.dll was not found.” Struggling to get past this point. Solution: Install vc redistributable x64. It should be fine.
Problem: Have a problem connecting in bench mode with the Audi A4 TEMIC VL300 CVT transmission control unit. Foxflash software cannot identify or read the unit. Attaching screenshots. Solution: Foxflash will read and write Temic VL300 gearbox TCU in boot mode. Don’t do it on bench mode. Don’t use Godiag GT107 gearbox adapter. Follow foxflash instructions to read VL300… Read More »
Problem: Foxflash unable to read any ecu, whenever it gets to 100% / to save the file, it throws an error saying “file saving error”. Anybody encounter this before? Solution: Reads fine, change saving folder. Change folder your saving your files AND use admin rights to run program. You don’t have rights to save in current folder… Read More »
Problem: Foxflash software is closing down when you start read/write. How to fix it? Possible solution: 99% this is the case of bad communication, so your internet is not good enough. Don’t share via wi-fi hotspot, use usb cable and DIRECT share internet via phone OR use lan connection. If still having problems, time to… Read More »
Problem: Mercedes Benz Sprinter 906 Delphi CRD 2.30 OM651 ECU. Obd read with foxflash. Stage 1 and DPF off. Read ok, Obd write with foxflash no luck, the car won’t start anymore. Solution: CRD2 (DCM3.5) is a known problematic protocol for foxflash. You need to use recovery function in kess2/kess3, not writing. Recovery with old Kess… Read More »
Problem: I bought the Foxflash equipment. It arrived yesterday. I put in my email and the phone number but the device says i already have a registered email. Error: “Another email is already registered with the code. Register with the correct email.” Solution: You bought it secondhand and YOU MUST USE previous owners email. You can register tool only… Read More »
