Tag Archives: Foxflash

Foxflash read and write Opel Astra 1.7Cdti 125HP 2012 ECU successfully. ECU type: Denso 64F7059 Dpf Off ok. Read/Write Full Bench without Bench Box. Checksum by foxflash.  

It’s a SSANGYONG ACTYON 2009, 2.0, 104kW. ECU type: Delphi DCM3.2AP Tool used: Foxflash Mode: BDM mode. BDM MPC 55x/56x full backup with foxflash. Checksum correction by foxflash, IMMO OFF ok. ST95320 eeprom write back with TL866II programmer for set write protect.

Renault SID306 ECU cloning is done with Foxflash programmer. Continental Sid306 Infineon TriCore SAK-TC1766 boot mode clone ecu. Need attention for pinout because very small in ecu pin. Cloning cannot be done on bench. Read in boot ok. Write in boot ok. Checksum by foxflash. Better keep power supply 12V+.    

Question:  Mitsubishi L200 2.2 110kw year 2019, need pinout for foxflash. Solution: Here’s the pinout. Read/write with foxflash ok. Checksum by foxflash.

Foxflash new user feedback: This is a Volvo ECU. Siemens sid803A. Done via foxflash. Read ok. Write ok. Checksum by foxflash. Note: It was under full system. Not in bench section. All done under 5 min. It worked without any problems.    

Foxflash read and write 2019 BMW 330i, Bosch MG1CS201 ECU on bench succesfully. Bench Read/Write ok. Checksum by foxflash. Stage 2. Had a non start at first but then found a bent ECU pin (they seem very soft on this ECU) . Pin sorted, faults cleared, car feeling fantastic.    

Problem: Foxflash failed to read VW DQ250 gearbox from Golf6 GTi on bench. Error no Flash, no Eeprom, no Backup? Solution: Your voltage is too low. You’re running way under 12v and doing DSG gearbox. Add 13volts and some amps. Then try again. On these 02E Foxflash works better than PCMflash. You need OBD to… Read More »

Foxflash read and write Mercedes B170 Siemens sim266 ECU in BDM successfully. Siemens sim266 Mercedes B170 Bdm mpc55x Read ok. Write ok. Checksum with foxflash. Keep voltage 13V. By foxflash all took around couple of minutes.  

Foxflash new user report: Volvo XC60 DENSO MB279700 ECU. Did it again via foxflash. Read unlock ok. Write ok. EGR OFF. Note: turn on off a couple times. When reading and unlock till you start procedure started See a lot people get error. Those who get error have something like 11.9-12.3volts. It can be done.… Read More »

Problem: Foxflash is unable to write a Bosch MD1CS003 ECU from Opel Corsa 2021 on bench mode. Read ok, write failed. Solution: This Bosch number is 0 281 037 101. 037 you cannot do it with Foxflash, even KESS3/Flex. It is locked. 034/035/036 versions are possible to read and write on bench mode. 037 is… Read More »

Foxflash user feedback: Ford Transit Custom SID211 ECU is bricked by other device. Successfully recovered this ECU with foxflash in boot mode. Car owner has original file on USB stick. He try flash his car and something happened because was no communication with ECU. First I read password, then flash. Some users reported read and… Read More »

Problem:  Foxflash failed to write a Citroen EDC17C60 ECU on bench mode, the software reported an error unlock failed. Any solution? Solution: You need to read password from file before write. You need to write original file, you extract password from original file put on same folders and write it. If you can’t write, that… Read More »

Problem 1: It’s an Audi a6 3.0tdi 2005 with Bosch EDC16CP34 ECU. Read and write with FoxFlash in bench mode. Ecu had been soft bricked and car didn’t start. Solution: Edc16cp34 has problem with checksum. Always do checksum manually (in winols/Lsuite etc).   User feedback: Feedback: Original ecu file from original-ecu website flashed back. Everything… Read More »

Foxflash read and write VW GOLF 1.6TDI 2017 ecu successfully. ECU Type: Delphi dcm6.2v Mode: OBD VR VR READ OK VR WRITE OK. It’s important to connect a power supply. Here read/write with voltage 14v.