With Flex 8.1.0.0, Magic Motorsport Flex is expanding its No RFT solution with support for even more Bosch MDG1 ECUs. More MDG1. More Freedom. Version 8.1.0.0 of Flex Out Now With the new Flex update, support to Boot Glitch mode introduced in the previous release expands. Newly supported: Bosch MD1CS069 TC299 – Fiat Ducato Bosch MD1CS001 TC298 – BMW… Read More »
Magic Motorsport Flex programmer released an important update yesterday: supports Bosch MDG1 ECU boot mode unlock without shipping (No RFT). Here comes the latest Flex user’s test report on BMW Bosch MG1CS201 encryoted ECU unlocking: It takes so long time. But finaly did it. Use standard Magic Motorsport power supply. Boot mode unlocking ok.… Read More »
Problem: Tried to clone VW Golf 8 DQ400E gearbox TCU with Magic Motorsport Flex programmer but won’t connect. All pinned up correctly and on power supply. Won’t connect at all. Can hear it when pinned up. Any advice? Solution: Some users reported that VW Golf 7 works fine but Golf 8 won’t connect. Use a… Read More »
Each serious tool on “pro” level has its own research and development team who daily push the boundries on what ecus/tcus tool can do by adding more protocols to list. Top 3 on actively still researching and developing more protocols with large userbase are autotuner,flex,kess v3. Top3 at the moment is autotuner (new upcomer, this… Read More »
Problem: After the last update Magic Motorsport Flex programmer software won’t work. It says error 2, please reinstall the application. Does somebody have a solution? Solution: Unistal flex, delete folder flex on HD. Reinstall app you can find the installer on Google if you don’t have subscription. Turn off antivirus. Run as administrator. … Read More »
Problem: It’s a Ford Transit 2018 with sid209 TC1797 ecu. Hardware number gk4a 12a650 ua. I’ve tried bitbox and Flex programmer. But hardware not compatible (obviously see hw not listed). Any solution? Solution: Sid209 GK4A version you need to boot unlock. Can’t write via obd straight away. Boot for readout, never had any luck with… Read More »
Problem: It’s a Silverado 2018 with ACDelco E41 ECM. Magic Motorsport Flex programmer can’t connect the ECU by obd bench. Any other suggestions? Solution: Need to unlock first via bench, tool will write a file direct to ecu, after finish can read file. E41 not enough VR files for public release. Hp tuners only solution… Read More »
Overview of the Volkswagen Audi SIMOS18 Series ECUs using Magic Motorsport Flex ECU programmer: The Volkswagen Audi SIMOS18 series ECUs (commonly referred to as “engine control computers”) can be confirmed to include the following model variants based on version classification: SIMOS18.1, SIMOS18.2, SIMOS18.3, SIMOS18.4, SIMOS18.5, SIMOS18.6, SIMOS18.7, and SIMOS18.10. These ECUs are utilized across multiple… Read More »
Iveco Bosch MD1CS069 Now Ready! New Flex update, version 7.49.0.0, now available, implementing OBD programming for the most modern Iveco vehicles equipped with Bosch MD1CS069, even those produced after 2021. Thanks to this new protocol, you can now work directly from the diagnostic port of the vehicle (bypassing the SGW module), or establishing direct connection through the connector. As of… Read More »
New protocol released of Magic Motorsport Flex programmer for Continental SID213 and SID213EVO engine units installed on new gen Ford and Volkswagen vehicles. This new solution is made to work on vehicles with 2.0L EcoBlue and 2.0L TDI engines. A new protocol that opens access to the map area via OBD connection, therefore… Read More »
Dq381 2023 is possible to read and write with Magic Motorsport Flex programmer? Car is VW Golf 8 R 2020. Here is the clue. That’s Gen2 you can try OBD and see what tool says. We did 2022, for 2023 report back. 401 bootloader will be locked. But most of these are no go.… Read More »
Renault Continental SID321 reading review: MMS Flex failed to read SID321 via OBD VR. It says no Virtual read available for this software version on the server. Cannot do it on bench when no vr on server. Did it with Alientech KESS3. Autotuner will also do this ECU. AT is the best in this ecu.
Tried to read and write Honda Accord Bosch EDC16C7 ECU with Magic Motorsport Flex ecu programmer. Doing CONNECT shows no ID information. But read and write went fine. AutoTuner failed to ID it also. So no read process started. So FLEX failed or didn’t showed up an ID but carried out reading and writing. This… Read More »
Magic Motorcport Flex read and write Audi A6 2021 MG1CS004 ECU successfully. HW version: 0040, H22 Audi a6 2021 Read via OBD VR. Write via OBD VR. such OBD2 VR driver is great. OBD2 straight forward for this HW number. Done a lots of them by OBD2. Also possible by bench for some sw versions.
Possible to clone VAG Delphi DCM6.2V ECU with Autotuner programmer? Yes in boot mode with Autotuner. 1:1 clone ok. Done with Autotuner few days ago no hassle. very easy just swap full backups in boot mode. If you read in boot and you write back the full backup. Need same part number and hw number.… Read More »
