Overview of the Volkswagen Audi SIMOS18 Series ECUs using Magic Motorsport Flex ECU programmer: The Volkswagen Audi SIMOS18 series ECUs (commonly referred to as “engine control computers”) can be confirmed to include the following model variants based on version classification: SIMOS18.1, SIMOS18.2, SIMOS18.3, SIMOS18.4, SIMOS18.5, SIMOS18.6, SIMOS18.7, and SIMOS18.10. These ECUs are utilized across multiple… Read More »
Iveco Bosch MD1CS069 Now Ready! New Flex update, version 7.49.0.0, now available, implementing OBD programming for the most modern Iveco vehicles equipped with Bosch MD1CS069, even those produced after 2021. Thanks to this new protocol, you can now work directly from the diagnostic port of the vehicle (bypassing the SGW module), or establishing direct connection through the connector. As of… Read More »
New protocol released of Magic Motorsport Flex programmer for Continental SID213 and SID213EVO engine units installed on new gen Ford and Volkswagen vehicles. This new solution is made to work on vehicles with 2.0L EcoBlue and 2.0L TDI engines. A new protocol that opens access to the map area via OBD connection, therefore… Read More »
Dq381 2023 is possible to read and write with Magic Motorsport Flex programmer? Car is VW Golf 8 R 2020. Here is the clue. That’s Gen2 you can try OBD and see what tool says. We did 2022, for 2023 report back. 401 bootloader will be locked. But most of these are no go.… Read More »
Renault Continental SID321 reading review: MMS Flex failed to read SID321 via OBD VR. It says no Virtual read available for this software version on the server. Cannot do it on bench when no vr on server. Did it with Alientech KESS3. Autotuner will also do this ECU. AT is the best in this ecu.
Tried to read and write Honda Accord Bosch EDC16C7 ECU with Magic Motorsport Flex ecu programmer. Doing CONNECT shows no ID information. But read and write went fine. AutoTuner failed to ID it also. So no read process started. So FLEX failed or didn’t showed up an ID but carried out reading and writing. This… Read More »
Magic Motorcport Flex read and write Audi A6 2021 MG1CS004 ECU successfully. HW version: 0040, H22 Audi a6 2021 Read via OBD VR. Write via OBD VR. such OBD2 VR driver is great. OBD2 straight forward for this HW number. Done a lots of them by OBD2. Also possible by bench for some sw versions.
Possible to clone VAG Delphi DCM6.2V ECU with Autotuner programmer? Yes in boot mode with Autotuner. 1:1 clone ok. Done with Autotuner few days ago no hassle. very easy just swap full backups in boot mode. If you read in boot and you write back the full backup. Need same part number and hw number.… Read More »
Problem: Tried to read 2006 VW mk5 gti DQ250C gearbox with Autotuner but failed. Is there going to be any update with support for DQ250C? Solution: DQ250C TCU is not supported by Autouner. AT has no support for Cxx. And it reads and writes DQ250 TCU slowly. Use KESS3 or Flex for DQ250C via OBD… Read More »
Problem: Foxflash failed to read a BMW MSD80 DME in E92 335i by OBD. Voltage is 13.6V. Solution: Foxflash MSD80 OBD takes long. For example, BMW 325i e93 took 30 min. Make sure you have a battery stabiliser hooked up. Write when quicker. Foxflash doesn’t have bench for this ecu. Remove the ECU out of… Read More »
Problem: VW Golf R DQ250F. Was writing mod file and Autotuner software gave an error now can’t ID or write (same data transfer failed error). Car is not starting and P light flashing on gearbox. Any solution? Solution: If fail write, never turn ignition off, try again write the modified file, if again fails, than… Read More »
Problem: I couldn’t read EDC17c74 with Flex programmer on bench i had read that ecu one year ago no problem. or maybe my flex box is the problem? Solution: Check if wires are not broken. It may stop working when wires were broken. EDC17 requires pin 4 in slot A as we can see in… Read More »
Question: For Dacia Duster with EMS3155 ecu, no problem to read write via flex full obd ? Here is the clue. Just read a normal obd protocol. For full obd, flex patch during ~45min Full obd, first time patch is long maybe 45 mins to 1hr but after that is quick Be careful if… Read More »
Dacia Duster 2021. Flex cannot read, kess3 yes. Bosch MD1CS016 ECU. Read micro = 16mb.
I just had an issue with this ECU while trying to perform a Full OBD read Renault SID307 with Flex programmer. At the moment of connection, Flex managed to read the password, and right after that it started patching the ECU. A few seconds later, the cooling fan turned on, and shortly after, during the… Read More »
