Problem: It’s a Volvo XC-60 with DENSO MB279700-96xx ECU. Original ecu has been flooded with water. Have read eprom on bench no problem same as whole ecu. MMS Flex says there is no clone. How to clone this ECU with Flex programmer? Feedback and solution: It turned out that after writing full backup in to… Read More »
I just had an issue with this ECU while trying to perform a Full OBD read Renault SID307 with Flex programmer. At the moment of connection, Flex managed to read the password, and right after that it started patching the ECU. A few seconds later, the cooling fan turned on, and shortly after, during the… Read More »
Alientech KESS3 released new OBD & OBD VR protocols for Marelli MM11MPHW002 ECUs- Aprilia and Moto Guzzi motorcycles. Unlock tuning on the latest supersport and modern classic platforms from the Piaggio group with KESS3 — including the full RS and Tuono lineup and the Moto Guzzi V7 — and expand your offer across the next… Read More »
How to read and clone the GPEC2 module? This module is used in Jeep, Chrysler, Dodge, and other American CDI vehicles. We will perform the process using the OBDStart DC706 ecu tool along with its MP001 adapter cable. Step-by-Step Process: Connection Setup First, we connect to the vehicle via OBD. Then, we navigate through the… Read More »
2015 Mercedes- C220D Delphi CRD3PLUS.A0 TC1797 ECU reading and writing review: Flex could not read/connect via Bench or even OBD- Tried both pinots, Tried TC1793 etc. Pulled out Foxflash with the same result. In the end completed with Autotuner worked first time. Very Strange as have done many of these before and there’s no info… Read More »
Problem: Read and write DCM6.2V Vag ECU with MMS Flex programmer. At 29% the write failed and car didn’t start, voltage was 13.3. Any solution? Solution: Do these without a charger. Probably an internet or server issue. Or do it in bootmode! OBD after 21 with flex maybe can damage eeprom. Never had an issue… Read More »
Problem: Cannot get Foxflash working today. Error: There is a problem reaching the update server. Solution: so here’s the quickfix from one of our users FOR THE UPDATE SERVER ERROR! Download link and unzip to foxflash folder, then make a shortcut on desktop of the foxflash software. https://files.fm/u/cn4dk6m6jz Be sure to install also drivers, found… Read More »
Problem: Tried to read and write Simos 18.1 ECU with Foxflash but extract password not working. Solution: Voltage is not good. User feedback: Solved! Had a problem with the resistances, the voltage is true, the power supply died and did it with the standard. READ OK. WRITE OK. CHEKSUM OK FOXFLASH. STAGE 1 +… Read More »
Alientech KESS3 released a new protocol for EVPT VCU3000- Citroen, Fiat, Opel/Vauxhall. Take the next step in EV tuning: work in BOOT mode on the latest EVPT VCU3000 units, now supported on ultra-compact electric vehicles equipped with 5.5 kWh systems from 2025. Full read and write access in BOOT mode Direct operations on the VCU… Read More »
Read and write Skoda Fabia 1.2 12V Siemens Simos 3PG ECU with Foxflash successfully. Lambda OFF. BOOT Read 2min. BOOT Write 4min. Checksum by Lsuite. FoxFlash does not correct the checksum for this type driver. Only self do with other software like Lsuite.
Alientech KESS3 released new protocols for next-generation off-highway and Marine engines. Work in BOOT and BENCH on vehicles and vessels designed for daily professional use. 01.12.2025 – UPGRADE 2.66 KESS3 continuously expands its support for the latest off-highway machines and Marine units, giving you new solutions to operate on construction equipment, industrial machinery, and marine… Read More »
FormulaFlash ECU TCU programmer released new software version 1.0.8.0 on December 1st, 2025. V1.0.8.0 Adds following ECU types: Volvo EDC15C11-3.XNO1 EDC15C11-4.X250KNO1 EDC15C11-4.X500KNO1 EDC15C11-3.XNO2 EDC15C11-4.X250KNO2 EDC15C11-4.X 500K NO2 EDC15C3 KLINE NO1 EDC15C3 KLINE NO2 EDC15C7 KLINE Opel ME1.55 KLINE ME7.6H4 KLINE ME7.6.1 KLINE ME7.6.2 KLINE ME7.6.1 KLINE ME7.6.2 KLINE JAGUAR P3.ONA 4.2SC, 4.2 V8 V8SC, 4.2SC… Read More »
OBDSTAR X300 Classic G3 worked very well today, had to do DTC off on a Peugeot boxer dcm6.2c. ECU type: DCM6.2C Mode: Boot mode. Read ext eeprom and int flash ok. Write eeprom and flash ok. Only had DCM6.2A listed but I know the pin out is the same. Worked great with fast read and… Read More »
Problem: No red light on Foxflash programmer bench box and switch, has happened to anyone? Solution: Light comes only when tool start reading, when it says keep ecu power on make sure switch is at 1, then press ok that’s when the light will come Power will only come on in bench mode after the… Read More »
Foxflash read and write Ford Connect MD1cs005 ECU on bench successfully. ADblue off. MD1cs005 Read/Write on Bench. Checksum by foxflash. Voltage 13.5.
