As titled, Flex and Autotuner which is better to read and write Renault / Dacia / Mitsubishi Continental EMS3160 ECU? OBD or bench? Autotuner is better on this ECU. Use AT, 99% of chance VR will be available. Autotuner>CMD>Flex, in this order. Obd and bench are based on VR. Flex does not work on some… Read More »
OBDSTAR DC706 read and write Kia Kefico cpegd 2.20.4 on bench. Read / write on bench all ok. as long as checksums are correct, all will be fine. Get them wrong and you will have to recover in boot mode with another tool. Read and write on the bench with manual checksum. And we are… Read More »
Problem: It’s a Peugeot 508 keyless model. Autotuner read DCM7.1A – Delphi OK via OBD, unlock ECU ok, but fail to OBD write after unlocking ECU. Solution: You have to hold and press key against the column the entire time if the writing yes. Follow instructions exactly. Hold the key in your hand throughout the… Read More »
Problem: Sid309 uds Nissan Qashqai J11 1.5 110bhp dci, flashed it with Autotuner via boot, plugged in ecu, fan is kicked in all the time and doesn’t start. Any suggestions? Solution: Bad file solution. Restore original.Flash it back to original Feedback: SORTED: was the file.
Alientech KESS3 released new protocol for Bosch EDC17CP52- Iveco Daily 2.3 and 3.0 FPT. Work in OBD, BENCH, and BOOT modes, now also with KESS3 truck and agri activation, on Iveco commercial vehicles for complete control over the most common FPT engines in Europe. Full access for EDC17CP52 ECUs Read, write, and clone safely and… Read More »
Problem: CG100X programmer has been activated but the device is not working, still asks for authorization. Any solution? Solution: 1.Provide CG100X device serial number to www.iecutoo.eu customer service to verify the device has been activated successfully. 2.If the device has been activated, go to Settings- About- Check and Fix to fix software. Then try again.
Alientech KESS3 released new procotol for Bosch EDC17C49- Iveco Daily 2.3 & 3.0 FPT. This is for the SGW protected ones. Operate in OBD, BENCH, and BOOT modes on Iveco light commercial vehicles and manage the most popular FPT engines in Europe with maximum flexibility and reliability. Full access via OBD, BENCH & BOOT. Read,… Read More »
Problem: Foxflash programmer reads Audi Bosch EDC16U31 ECU ok, but failed to write this ECU on bench. Any solution? Solution: First voltage is too low, try to write with voltage over 13.5V. Second, it can be up to checksum. Make cheksum on winols, not with foxflash. Don’t do checksum automatically when writing back original. If… Read More »
SUCCESS!!.. Porsche lithium battery repair using CG100X programmer successfully. Menu path: Porsche 12V Lithium battery- Caynne- 2020- SPC5644B. Have original workinging file came from a brand new lithium battery BMS, and the CG100X programmer has capability to repair file too.
Problem 1: It’s an Audi a6 3.0tdi 2005 with Bosch EDC16CP34 ECU. Read and write with FoxFlash in bench mode. Ecu had been soft bricked and car didn’t start. Solution: Edc16cp34 has problem with checksum. Always do checksum manually (in winols/Lsuite etc). User feedback: Feedback: Original ecu file from original-ecu website flashed back. Everything… Read More »
Foxflash read and write VW GOLF 1.6TDI 2017 ecu successfully. ECU Type: Delphi dcm6.2v Mode: OBD VR VR READ OK VR WRITE OK. It’s important to connect a power supply. Here read/write with voltage 14v.
Foxflash read and write Mercedes Actros MP4 MCM 2.1 and ACM all ok. It works well on all series of MCM and ACM from Actros MP4. Read the flash and eeprom using the bench method. Actros MP4 MCM 2.1 D3 full read and write ok, full system bench mode. Voltage 14V. Actros ACM 2.1 full… Read More »
Problem: Tried to read and write Porsche med17.1.6 (tc1797) ECU with foxflash. Reading was okay with the original but I can’t write with new one is there any idea or tips about this type? Error: Uncorrect file 014000-OTP sector not writable. Solution: So need to import ONLY maps, now theres changes on otp area on… Read More »
Foxflash read and write Citroen Jumper 2.2 ecu Visteon DCU 102 successfully. Read ECU in boot mode. Foxflash will read Ford Visteon DCU by OBD, PSA cannot. Write ECU via OBD. It stopped for a moment at 60%, it said it was checking the checksum, but then the writing continued fine. The writing took about… Read More »
CG FC200 read and write Opel ASTRA K DELCO E98 ECM on bench mode successfully. Model: Astra K 1600 CDTI B16DTH 136 ECU: Delco E98 Read eeprom Read flash Write eeprom Write flash all ok.
