Problem: No red light on Foxflash programmer bench box and switch, has happened to anyone? Solution: Light comes only when tool start reading, when it says keep ecu power on make sure switch is at 1, then press ok that’s when the light will come Power will only come on in bench mode after the… Read More »
Foxflash read and write Ford Connect MD1cs005 ECU on bench successfully. ADblue off. MD1cs005 Read/Write on Bench. Checksum by foxflash. Voltage 13.5.
Problem: How do I read and write down a driver in a vw dcm6.2v with foxflash in boot mode, because after installing stage 1 (via OBD) the car does not start and I can’t bet anything? Solution: That situation usually comes from checksum handling or wrong patch area – DCM6.2V is picky. If you can… Read More »
Problem: I have this alert today when I open the Foxflash software. It says the subscription is about to expire. Solution: Ignore, there’s no subscription. Hit OK and continue.
Read and write BMW 520d EDC17C41 ECU with Foxflash successfully. Read ok. Write ok. Checksum correction. Stage 2, EGR off. Car feeling great.
Foxflash read and write Opel Astra 1.7Cdti 125HP 2012 ECU successfully. ECU type: Denso 64F7059 Dpf Off ok. Read/Write Full Bench without Bench Box. Checksum by foxflash.
It’s a SSANGYONG ACTYON 2009, 2.0, 104kW. ECU type: Delphi DCM3.2AP Tool used: Foxflash Mode: BDM mode. BDM MPC 55x/56x full backup with foxflash. Checksum correction by foxflash, IMMO OFF ok. ST95320 eeprom write back with TL866II programmer for set write protect.
24.11.2025 – UPGRADE 2.65 The protocols you were waiting for are now finally active on Alientech KESS3. Ford’s evolution continues through increasingly efficient powertrains, new electronic management systems, and Bosch platforms designed to enhance performance and safety. With this update, KESS3 takes a decisive step forward, enabling OBD access to the latest-generation MD1 and MG1… Read More »
OBDSTAR DC706 read and write Hyundai SIM2K-251 ECM in boot mode successfully. With MP001 programmer in boot mode. First tried SIM2K-251 in boot, no luck. Sim2k-251 be able to read with sim2k-250 in boot mode. Checksum correction by DC706. Immo off on Sim2k-251 is not working. SIM2k-250 don’t have immo off options as you see… Read More »
Read and write the Maserati BCM/BSI module with Xhorse multi prog successfully. MASERATI BCM Type: Magneti Marelli BSI Processor: MC9S12DG256 unsecured Read mcu, eeprom and flash successfully on bench mode. vvdi prog will also read this BCM.
Alientech KESS3 released new protocol fpr HJS ACU- CompAir, Landini, McCormick. Operate in BOOT mode on next-generation agricultural and industrial machines, expanding your service options on some of the most requested work vehicles in the field. Read and write in BOOT mode on the HJS ACU control unit Work with precision on 4.5L and 6.7L… Read More »
Renault SID306 ECU cloning is done with Foxflash programmer. Continental Sid306 Infineon TriCore SAK-TC1766 boot mode clone ecu. Need attention for pinout because very small in ecu pin. Cloning cannot be done on bench. Read in boot ok. Write in boot ok. Checksum by foxflash. Better keep power supply 12V+.
Alientech KESS3 released new protocol for Continental PTM5- MAN 12.4L trucks. Operate in BOOT mode on European heavy-duty vehicles thanks to the latest update dedicated to MAN engines. Read and write the ECU in BOOT mode. Work safely on 12.4L engines across the most reliable MAN series. Improve efficiency and overall performance on long-haul and… Read More »
OBDSTAR DC706 read and write VW up with ME17.5.24 ecu, start breaker remove. Read eeprom & flash ok. Write eeprom and flash ok. Checksum by DC706. DC706 will also read immo data, decrypt immo data, write VIN and IMMO OFF for this ECU. Did a few already for VW and Audi, worked great. mp001 is… Read More »
Problem: What’s going on with the Magic Motorsport Flex programmer? Cannot see device SN, no connection. Solution: Possible solutions: There is no usb connection. Change cable or port. Reinstall new software from mms and it will be fixed Go to your mms page and download it and see how it works Go to the help… Read More »
